RiffRaff, a villain on Underdog, from an American Saturday morning animated tv collection that ran from 1964, to 1967.
Riffraff is an anthropomorphic wolf gangster. He leads an unnamed gang that always perform varied crime waves till they’re stopped by Underdog. He’s portrayed as extra of a comic book aid minor villain.
No helps are required. When you have the right filament colours, no portray is required.
This mannequin is the underside a part of an entire mannequin with my beforehand launched Underdog mannequin. As a result of slicing on the prime of the pinnacle to suit with Underdog, this mannequin ought to solely be printed together with the Underdog mannequin.
The assembled Underdog/RiffRaff mannequin is 255mm tall with a base of 171x171mm (matches on a Prusa Mini)
Get pleasure from!
……………………………………………………………………………………………..
Particular shoutout to maker Benoît Lussier for offering QA printing and high quality suggestions.
Particular because of Jason McMillan (makerworld ID Gatekeeper) for creating the Bambu Print Profile.
……………………………………………………………………………………………..
Print Directions:
Helps: no helps are required
Decision: .2mm
Infill: 15%
Constructing the mannequin
Colours
Black: (Satan Designs PLA – Black)
r_eyes_blacks (file incorporates two an identical items)
r_shirt
r_eyebrow_right
r_eyebrow_left
r_nose
r_head_black
..
Pink/Purple: (CookieCad PLA – Lavender)
r_eye_rim_right
r_eye_rim_left
..
Gentle Gray: (Paramount3d PLA – Prototype Gray)
r_ear_right
r_ear_left
r_mouth
..
Yellow: (Paramount3d PLA – Simpson Yellow)
r_eyes_yellow (file incorporates two an identical items)
r_tie
..
Darkish Gray: (Paramount3d PLA – Prototype Gray)
r_jacket
..
Brown: (Hatchbox PLA – Brown)
base_inside
..
Speckled Gray: (Paramount3d – Medusa Stone Gray)
base
..
White: (Satan Designs PLA – White)
r_eyewhite_left
r_eyewhite_right
r_head_white
r_star
r_hand
..
Any coloration (hidden piece)
pin_head
..
……………………………………………………………………………………………..
Printing and meeting ideas
Printing ideas:
1 – No helps are required
2 – There are some items that will want brims or rafts, use your discretion. When organising my prints I want to be conservative to make sure the least probability of a print failure, particularly for the reason that base of many components are hidden when inserted into one other half.
*I used a brim on:
r_hand
3 – When eradicating components from the printer mattress, it is a VERY good thought to put left/proper components into separate containers to assist with the meeting course of. Typically the distinction between the left and proper components may be very small however it’s nonetheless value protecting monitor of them (particularly if you happen to dimension up the mannequin considerably) and assembling them of their correct place.
..
Meeting ideas:
1 – Take your time gluing the mannequin collectively and benefit from the course of. Dry match all of the components and provides some thought into which components to connect collectively as teams after which gluing the teams collectively. Let the glue for every group set fully earlier than combining teams.
2 – I used 3D Gloop and E6000 to place this mannequin collectively. Every kind of glue has completely different execs/cons and I discovered that quick drying 3D Gloop was far simpler to make use of than superglue (for me). The E6000 sticky glue permits extra time to place components and continues to be the very best for smaller components. For each glues utilizing a smaller quantity is normally higher than extra glue.
3 – Gluing/assembling this mannequin is straight ahead. The mannequin may be glued fully after which joined with the Underdog mannequin (posted individually).
4 – An FYI for my fashions. Sometimes the mattress facet of a component is the facet that’s inserted into one other half. For this mannequin the r_eyes_blacks and r_eyebrow_right/left are an exception and the mattress facet faces out, making meeting a lot, a lot simpler for these components.
5 – Check with the meeting diagrams within the footage part in addition to the uploaded footage for placing the mannequin collectively. The mannequin is supposed to be glued.
As famous to start with of this writeup, this mannequin is to be mixed with my beforehand launched Underdog mannequin
Don’t hesitate to ask questions, suggestions is important to creating higher fashions.
